How to Replace a Discontinued Linear Guide

To replace a discontinued linear guide, do not start by searching for the same nominal rail size. Start by identifying the original guide as completely as possible, then compare the replacement’s rail profile, carriage geometry, mounting-hole pattern, rail height, block height, load ratings, preload or clearance, accuracy class, lubrication, and mounting requirements.

The goal is not merely to find a guide that is “close.”

The goal is to determine whether the replacement can:

  • fit the existing machine

  • preserve the required mounting geometry

  • carry the actual loads

  • maintain the required stiffness and accuracy

  • work with the existing rail or carriage where appropriate

  • avoid unnecessary machine modification

Linear Automation USA specifically offers interchange assistance for discontinued linear systems, and in some cases a modern replacement may be designed to work directly with an existing legacy rail or mounting configuration. For example, Linear Automation USA currently lists Schaeffler KWLT15-H-V2-G4 as an interchangeable replacement for the corresponding Ewellix LLT configuration.

The most important rule is:

Nominal rail size alone does not establish interchangeability.

Why Replacing a Discontinued Linear Guide Can Be Difficult

A discontinued linear guide may have been installed on a machine 10, 20, or even 30 years ago.

By the time replacement is needed:

  • the original manufacturer may have changed ownership

  • the series may have been renamed

  • the product may have been redesigned

  • the catalog may no longer be easy to find

  • the carriage may be obsolete while the rail remains usable

  • the entire rail-and-block family may be discontinued

  • the original part number may be unreadable

This is why replacement work often becomes an engineering identification problem.

The question is not simply:

“What replaces this part number?”

It is:

“What current guide system can preserve the machine interfaces and performance that matter?”

Start With the Original Part Number

If the original rail or carriage still has a readable marking, document it before disassembly.

Record:

  • manufacturer

  • series

  • carriage part number

  • rail part number

  • size

  • preload or clearance code

  • accuracy code

  • seal or accessory codes

  • special suffixes

Photograph the marking from several angles.

Do not ignore suffixes.

A suffix can identify:

  • long vs. standard carriage

  • flange vs. narrow block

  • preload

  • accuracy

  • seal configuration

  • lubrication option

  • stainless material

  • special coating

Two blocks that look nearly identical can differ significantly in application behavior.

If the Part Number Is Missing, Measure the Guide

When no usable part number exists, measure the physical system.

At minimum, record:

  • rail width

  • rail height

  • carriage width

  • carriage height

  • carriage length

  • mounting-hole spacing on the block

  • rail mounting-hole pitch

  • rail hole diameter

  • rail end distances

  • overall rail length

  • number of blocks

  • rail spacing

  • block spacing

Also photograph:

  • rail profile

  • carriage top

  • carriage side

  • grease fitting

  • seals

  • mounting hole pattern

  • machine mounting surface

These details often make identification possible even when the original label is gone.

Do Not Trust Nominal Size Alone

One of the most common mistakes is assuming:

“It is a size 25 rail, so any size 25 guide will work.”

That is not safe.

Two nominally similar size-25 guides may differ in:

  • rail width

  • rail height

  • carriage height

  • carriage width

  • carriage mounting holes

  • rail hole pitch

  • rail shoulder geometry

  • lubrication-port position

  • preload

  • accuracy

  • load capacity

A replacement must be evaluated dimension by dimension.

Determine Whether You Need a Carriage Only or the Entire Guide System

This is one of the most important decisions.

There are three common replacement scenarios:

1. Direct Carriage Replacement

A new carriage can operate on the existing rail.

This is the ideal case because it may avoid:

  • rail removal

  • machine realignment

  • new mounting holes

  • machine downtime

But the manufacturer or supplier should confirm interchangeability.

2. Rail-and-Carriage Replacement

The old carriage is no longer compatible with any current block.

In that case, both the rail and carriage are replaced.

3. Engineered Interchange

A current guide from another series or manufacturer can replace the legacy system with:

  • minimal mounting changes

  • adapter plate

  • different fasteners

  • new rail holes

  • modified carriage mounting pattern

This can still be a good solution if the modification is understood before the replacement is ordered.

When Is a Carriage Interchangeable With an Existing Rail?

A carriage should only be treated as interchangeable when the manufacturer or a reliable cross-reference confirms compatibility.

THK, for example, now offers its GK Series as an explicitly interchangeable product family. THK states that compatible blocks and rails can be combined within the applicable series, accuracy class, and preload class, while also noting that interchangeable products have application limits and can differ from set products.

That illustrates an important principle:

Interchangeability is a product-system property, not something you can assume from physical appearance.

Match the Rail Profile

If you want to retain the existing rail, the replacement block must match the rail raceway geometry.

That includes:

  • rail cross section

  • raceway position

  • ball or roller contact geometry

  • internal clearance relationship

A block that physically slides onto the rail is not automatically safe or correct.

If the manufacturer does not confirm compatibility, replace the rail and block as a matched system.

Match the Carriage Mounting Height

One of the most important replacement dimensions is the assembled height from:

machine rail mounting surface → carriage mounting surface

If the replacement block is taller or shorter, the moving table may no longer align with:

  • ball screw

  • belt drive

  • actuator

  • tooling

  • adjacent rails

  • machine centerline

A small height difference can force a substantial redesign.

Match the Carriage Width

Carriage width affects:

  • mounting footprint

  • clearance around nearby components

  • table design

  • bolt spacing

  • support geometry

A wider block may interfere with machine structure.

A narrower block may require a new adapter or mounting plate.

Match the Carriage Bolt Pattern

Record:

  • hole spacing across width

  • hole spacing along length

  • thread size

  • tapped vs. through-hole mounting

  • bolt insertion direction

THK’s current product families illustrate how block styles within the same broader guide series can have different mounting configurations. For example, some HSR blocks are flange style with bolts from above and below, while others use narrower tapped-hole arrangements.

That is why:

same rail family does not necessarily mean same carriage mounting pattern.

Match Rail Mounting-Hole Pitch

If the machine base already contains tapped rail holes, rail-hole pitch becomes critical.

Verify:

  • center-to-center pitch

  • hole diameter

  • counterbore or countersink

  • first-hole end distance

  • last-hole end distance

If the replacement rail uses a different pitch, you may need:

  • new tapped holes

  • adapter plate

  • custom rail machining

  • machine-base modification

For retrofit work, the hole pattern can be just as important as the load rating.

Match the Rail Height and Width

The replacement rail must also fit the machine datum.

Check:

  • rail width

  • rail height

  • shoulder location

  • corner radius

  • bolt-hole geometry

If the rail is narrower or wider, the existing reference shoulder may no longer position it correctly.

If the rail height changes, the complete assembly height changes as well.

Match Load Capacity

Physical fit is only the first test.

The replacement must carry the application load.

Evaluate:

  • dynamic load rating

  • static load rating

  • actual block loads

  • moment loads

  • acceleration

  • emergency-stop loads

  • process forces

THK’s guide-selection methodology explicitly considers applied load, equivalent load, preload, static safety factor, average load, and nominal life before final selection.

A guide that fits dimensionally but has inadequate capacity is not a suitable replacement.

Do Not Compare Dynamic Load Rating Alone

Two guides can have similar dynamic ratings but different:

  • static ratings

  • moment capacity

  • stiffness

  • internal geometry

  • preload options

  • service-life behavior

Replacement should be based on the entire application.

This is particularly important when the old machine carries:

  • cantilevered tooling

  • tall payloads

  • large overhung loads

  • cutting forces

Match or Recalculate Moment Capacity

Moment loading can govern guide selection.

A replacement guide should be checked for:

  • pitch

  • yaw

  • roll

If the replacement block is shorter, its moment capability may differ.

If rail spacing or block spacing changes during the retrofit, the load reactions can change as well.

Do not assume that equal payload weight means equal guide loading.

Match Preload or Clearance

Preload affects:

  • rigidity

  • resistance

  • accuracy

  • sensitivity to mounting error

THK’s interchangeable GK products specifically treat radial clearance or preload as a relevant selection characteristic.

A replacement block with significantly higher preload can make an older machine:

  • harder to move

  • more sensitive to rail alignment

  • more sensitive to poor mounting surfaces

A replacement with substantially more clearance may reduce machine rigidity.

Match Accuracy Requirements

Consider:

  • running parallelism

  • dimensional height tolerance

  • dimensional width tolerance

  • variation among blocks

  • machine positioning requirement

THK publishes accuracy standards and mounting tolerances as product-specific data for current HSR and SHS families.

Do not replace a high-accuracy guide with a standard-accuracy product simply because the dimensions match.

Check Mounting Surface Requirements

A modern replacement may have different tolerance expectations from the original guide.

Review:

  • base flatness

  • rail parallelism

  • vertical level

  • shoulder height

  • corner radius

  • reference surfaces

THK specifically publishes mounting-surface accuracy requirements for current guide families, and some models identify recommended values tighter than the maximum permissible value.

If an old machine base is damaged or worn, inspect it before installing the new guide.

Inspect the Existing Machine Base Before Ordering

Look for:

  • fretting

  • corrosion

  • dents

  • burrs

  • raised material

  • elongated holes

  • worn reference shoulders

  • crash damage

  • old shims

  • hand grinding

  • previous repair modifications

A replacement guide should not be installed blindly onto a damaged base.

If the original guide failed prematurely, the mounting structure may have contributed.

Measure Rail Spacing

For two-rail systems, measure the center-to-center spacing between rails.

This matters when considering:

  • replacement rail width

  • carriage width

  • table fit

  • moment reactions

  • mounting-hole location

If the new rail system changes rail spacing, block loads may change as well.

Measure Block Spacing

Block spacing influences:

  • pitch-moment capacity

  • yaw-moment capacity

  • table rigidity

  • load distribution

A replacement carriage that is significantly longer or shorter may change the available block-center spacing even if it fits the table.

Check the Moving Table

The moving table may be the most restrictive part of the retrofit.

Measure:

  • carriage mounting-hole pattern

  • mounting-pad height

  • available width

  • bolt access

  • nearby obstructions

A replacement rail system can sometimes fit the machine base but not the table.

Check the Drive System

The guide is usually connected mechanically to another motion component.

That may be:

  • ball screw

  • belt

  • rack and pinion

  • linear motor

  • pneumatic actuator

  • electric cylinder

Changing guide height or table position can create misalignment with the drive.

Before approving a replacement, verify:

guide geometry + drive geometry

together.

Check Lubrication Arrangement

The old machine may use:

  • manual grease fittings

  • remote grease lines

  • centralized lubrication

  • oil system

Confirm that the replacement carriage supports an appropriate lubrication method.

Also check:

  • fitting location

  • access

  • mounting orientation

  • grease compatibility

A direct dimensional replacement is not ideal if the grease fitting becomes inaccessible inside the assembled machine.

Check Environmental Requirements

If the original machine operates around:

  • coolant

  • metal chips

  • abrasive dust

  • humidity

  • water

  • washdown

  • high temperature

  • low temperature

the replacement may need:

  • enhanced seals

  • scrapers

  • special grease

  • corrosion-resistant material

  • coatings

  • rail covers

The replacement should solve the actual application, not merely recreate the original dimensions.

Check Rail Length

Measure the actual installed rail.

Do not rely only on the old catalog’s standard-length table.

The original rail may have been:

  • custom cut

  • shortened during installation

  • jointed

  • special length

Record:

  • overall length

  • mounting-hole pitch

  • end-hole distances

Linear Automation USA offers custom-cut rail processing, which can be particularly useful when replacing obsolete guideways whose original standard length is no longer available.

Can You Cut the Replacement Rail to Match the Old One?

Often, yes—if the new rail family supports cut-to-length processing and the required hole geometry can be preserved.

Before cutting, verify:

  • pitch

  • first-hole distance

  • last-hole distance

  • minimum end material

  • rail length

  • mounting base holes

The correct replacement length should be based on the machine’s actual hole pattern, not merely the old rail’s nominal catalog length.

Should You Replace All Carriages?

That depends on the guide system and failure mode.

If the rail remains serviceable and the manufacturer confirms block interchangeability, a single carriage may sometimes be replaced.

But if:

  • the rail is damaged

  • other blocks show wear

  • the system is matched

  • the legacy block is no longer compatible

  • preload or accuracy cannot be preserved

a full system replacement may be more appropriate.

Should You Replace Both Rails?

On a two-rail machine, replacing both rail systems may be appropriate when:

  • both are worn

  • the legacy series is obsolete

  • the new family changes geometry

  • the machine accuracy requires matched components

  • partial retrofit would create mixed performance

However, a one-rail replacement can sometimes be practical if the exact replacement is confirmed and the other guide remains serviceable.

Direct Replacement vs. Engineered Retrofit

A replacement can fall into three levels.

Level 1: True Interchange

The new carriage or rail is specifically approved to interchange with the old system.

Minimal machine change is required.

Level 2: Dimensional Replacement

The new guide does not share the original rail but the complete replacement system fits the existing machine geometry.

Possible changes may include:

  • different fasteners

  • different rail length

  • minor hole changes

Level 3: Engineered Retrofit

The replacement guide requires:

  • adapter plate

  • new mounting holes

  • different table interface

  • changed rail spacing

  • drive realignment

This can still be economically worthwhile compared with replacing the machine.

A Current Example: Schaeffler / Ewellix Interchange

Linear Automation USA currently lists the Schaeffler KWLT15-H-V2-G4 carriage as an interchangeable replacement corresponding to an Ewellix LLT configuration.

The product listing states that the Schaeffler carriage is intended to match the corresponding Ewellix rail profile and mounting configuration when the correct equivalent is selected.

This is the type of replacement that can preserve an existing system without forcing a full rail-and-carriage changeout.

But that should not be generalized to every Schaeffler, Ewellix, or legacy linear guide.

The exact interchange must still be confirmed by part number.

Why Manufacturer Cross-References Matter

A manufacturer cross-reference can provide much stronger evidence than visual similarity.

Useful cross-reference information may confirm:

  • legacy part number

  • current equivalent

  • rail compatibility

  • carriage style

  • preload

  • accuracy

  • dimensions

Where a verified interchange exists, use it.

Where one does not exist, treat the project as a full engineering comparison.

ISO Dimensions Can Help—but Do Not Prove Full Compatibility

Current linear guide families increasingly use standardized dimensional frameworks.

THK, for example, states that its GK interchangeable guide family includes products with standardized mounting dimensions compliant with ISO 12090-1 or ISO 12090-2.

That can improve replacement possibilities.

However:

standard mounting dimensions do not automatically make every manufacturer’s rail and carriage operationally interchangeable.

Raceway geometry, preload, accuracy, rail/block pairing, and other details still matter.

What If No Direct Replacement Exists?

If no confirmed interchange exists, evaluate whether a modern guide can be installed with acceptable machine modifications.

Typical solutions include:

  • adapter plate under carriage

  • adapter plate under rail

  • new tapped rail holes

  • new carriage mounting holes

  • custom-cut replacement rail

  • modified table

  • altered reference shoulder

The objective is to minimize modification while preserving:

  • stiffness

  • alignment

  • load capacity

  • serviceability

Adapter Plates Can Be Useful

A carefully engineered adapter plate can solve:

  • carriage height difference

  • bolt-pattern difference

  • width difference

But the adapter adds another structural interface.

Evaluate:

  • plate thickness

  • rigidity

  • flatness

  • fasteners

  • available machine clearance

Do not use a thin flexible plate simply to make hole patterns match.

Avoid Hand-Drilled Retrofit Geometry Where Precision Matters

A precision guide should be mounted to controlled geometry.

If new holes are required, establish them from a defined datum.

Random hand drilling can introduce:

  • rail misalignment

  • inaccurate spacing

  • bolt interference

For higher-accuracy equipment, machine the modification rather than improvising it during installation.

Consider Whether the Retrofit Is an Opportunity to Improve the Machine

A discontinued guide replacement can sometimes correct weaknesses in the original machine.

Possible improvements include:

  • better sealing

  • easier lubrication access

  • higher rigidity

  • improved load capacity

  • easier future replacement

  • currently stocked guide family

  • custom-cut rail availability

The goal should not always be to reproduce an obsolete system exactly.

Sometimes the better answer is a modernized equivalent.

Do Not Oversize Without Checking the Consequences

A larger guide may offer greater capacity, but it can also create:

  • higher assembly height

  • wider carriage

  • different mounting holes

  • increased mass

  • clearance problems

The best replacement is not necessarily the largest guide that fits roughly in the machine.

It is the guide that meets:

performance + geometry + serviceability

requirements.

Replacement Procedure: Step by Step

Step 1: Identify the Legacy Guide

Collect:

  • manufacturer

  • part number

  • rail series

  • size

  • photographs

Step 2: Measure the Existing System

Record:

  • rail width and height

  • block dimensions

  • assembly height

  • block hole pattern

  • rail hole pitch

  • rail length

Step 3: Document Machine Geometry

Measure:

  • rail spacing

  • block spacing

  • mounting shoulder

  • table mounting pattern

  • drive-system alignment

Step 4: Document Application Requirements

Record:

  • payload

  • center of gravity

  • process force

  • speed

  • acceleration

  • stroke

  • duty cycle

  • environment

Step 5: Search for a Verified Cross-Reference

First determine whether:

  • the original manufacturer offers a successor

  • another manufacturer has a verified interchange

  • an interchangeable carriage can use the original rail

Step 6: Compare Dimensions

Build a side-by-side dimensional table.

Step 7: Compare Performance

Check:

  • dynamic load

  • static load

  • moment capacity

  • preload

  • accuracy

  • rigidity

Step 8: Compare Installation Requirements

Check:

  • rail holes

  • reference shoulder

  • mounting height

  • carriage bolts

  • lubrication

Step 9: Determine the Retrofit Level

Decide whether it is:

  • direct interchange

  • dimensional replacement

  • engineered retrofit

Step 10: Inspect the Machine Base

Correct any damage before installing the replacement.

Step 11: Install and Align

Follow the replacement manufacturer’s installation procedure.

Step 12: Verify the Complete Axis

Check:

  • smooth travel

  • alignment

  • drive loading

  • full stroke

  • lubrication

  • final machine accuracy

Replacement Comparison Worksheet

ParameterExisting GuideProposed ReplacementManufacturerSeriesRail sizeRail widthRail heightCarriage heightCarriage widthCarriage lengthBlock hole patternRail hole pitchOverall rail lengthDynamic load ratingStatic load ratingPreload / clearanceAccuracy classLubricationSeal configurationDirect interchange confirmed?Machine modification required?

This simple table can prevent a large number of expensive replacement mistakes.

Common Mistakes When Replacing a Discontinued Linear Guide

Matching Only the Rail Width

Rail width does not establish compatibility.

Matching Only the Part Number Prefix

Suffixes often matter.

Assuming Same Nominal Size Means Same Guide

It does not.

Ignoring Preload

A dimensionally similar guide can behave very differently.

Ignoring Accuracy Class

A standard guide may not preserve a precision machine’s performance.

Ignoring Rail Hole Pitch

This can turn a simple replacement into a machine-base modification.

Ignoring Assembly Height

A few millimeters can misalign the entire drive.

Replacing the Carriage Without Inspecting the Rail

A damaged rail can quickly damage the new carriage.

Copying the Original Guide Without Checking Why It Failed

The machine may have outgrown the original design.

Assuming ISO Dimensions Guarantee Interchangeability

Standard dimensions help, but full interchange must still be verified.

Linear Automation USA's Perspective

At Linear Automation USA, discontinued linear-guide replacement is one of the applications where careful identification matters most.

We do not start with:

“What size rail is this?”

We start with:

“What machine interfaces and operating requirements must the replacement preserve?”

For an interchange project, we want to know:

  • original manufacturer

  • full part number

  • photographs

  • rail width and height

  • carriage dimensions

  • mounting-hole pattern

  • rail-hole pitch

  • rail length

  • rail spacing

  • block spacing

  • payload

  • center of gravity

  • speed

  • acceleration

  • application environment

From there, the replacement can be classified as:

  • verified interchange

  • close dimensional replacement

  • engineered retrofit

Our goal is to preserve as much of the existing machine as practical while avoiding an interchange that only appears correct.

Linear Automation USA specifically offers interchange services for discontinued linear systems and supplies current profile rail systems from SBC Linear, WON Linear, and Schaeffler.

For a legacy guide that is difficult to identify, contact Linear Automation USA with photographs and measurements.

Discontinued Linear Guide Replacement Checklist

Before ordering:

  1. Record original manufacturer.

  2. Record full carriage part number.

  3. Record rail markings.

  4. Photograph the system.

  5. Measure rail width.

  6. Measure rail height.

  7. Measure carriage height.

  8. Measure carriage width.

  9. Measure carriage length.

  10. Record carriage bolt pattern.

  11. Record rail mounting-hole pitch.

  12. Measure rail length.

  13. Measure rail spacing.

  14. Measure block spacing.

  15. Record payload.

  16. Record center of gravity.

  17. Record process forces.

  18. Record speed and acceleration.

  19. Confirm preload or clearance.

  20. Confirm accuracy requirement.

  21. Confirm lubrication arrangement.

  22. Search for verified manufacturer interchange.

  23. Compare load ratings.

  24. Compare mounting geometry.

  25. Determine machine modifications before ordering.

Frequently Asked Questions

How Do I Replace a Discontinued Linear Guide?

Identify the exact original guide, measure the existing rail and carriage geometry, determine whether a verified interchange exists, and compare the proposed replacement’s dimensions, load ratings, preload, accuracy, lubrication, and mounting requirements before ordering.

Can I Replace Only the Carriage?

Sometimes. If the manufacturer confirms that the new carriage is interchangeable with the existing rail, replacing only the block may be possible. Otherwise, the complete rail-and-carriage system should be considered.

Are Linear Guide Blocks Interchangeable Between Brands?

Not automatically. Similar nominal dimensions do not prove compatibility. Use a verified cross-reference or replace the rail and carriage as a matched system.

Can a Schaeffler Carriage Replace an Ewellix Carriage?

Some specific Schaeffler/Ewellix combinations are identified as interchangeable. Linear Automation USA, for example, currently lists KWLT15-H-V2-G4 as a corresponding Ewellix LLT interchange. The exact part number must still be verified.

Can I Replace a Size 25 Linear Guide With Any Other Size 25?

No. Nominal size alone does not establish rail profile, carriage dimensions, hole pattern, preload, accuracy, or load compatibility.

Do I Need to Replace the Rail With the Carriage?

If the new block is not explicitly compatible with the existing rail, replacing both is generally the safer approach.

Can a New Rail Be Cut to the Same Length as the Old Rail?

Often, yes, if the replacement family supports custom cutting and the mounting-hole geometry can be preserved. Check pitch and end-hole positions before cutting.

What If the New Rail Has Different Mounting-Hole Spacing?

The machine may require new tapped holes, an adapter plate, or another engineered modification.

What If the Replacement Carriage Is a Different Height?

The table or drive system may require an adapter or redesign. Assembly height should be checked before ordering.

Does ISO 12090 Mean All Linear Guides Are Interchangeable?

No. ISO-standardized mounting dimensions can improve dimensional compatibility, but complete operational interchange still depends on the specific rail/block system, accuracy, preload, geometry, and manufacturer guidance. THK explicitly limits interchangeability claims to applicable GK products and conditions.

Should I Upgrade to a Larger Guide While Replacing the Old One?

Only if the application analysis justifies it. Larger guides can change mounting dimensions and machine geometry.

What If I Cannot Identify the Original Part Number?

Photographs and accurate measurements of the rail, carriage, mounting holes, and machine geometry can often support identification or an engineered replacement.

Need Help Replacing a Discontinued Linear Guide?

For the fastest interchange evaluation, provide:

  • clear photos of the carriage

  • clear photos of the rail

  • all visible part numbers

  • rail width and height

  • carriage width, height, and length

  • carriage mounting-hole spacing

  • rail mounting-hole pitch

  • rail length

  • number of rails

  • number of blocks

  • rail spacing

  • block spacing

For help with a discontinued guide, use Linear Automation USA’s contact page.

Recommended Reading

Schaeffler Linear Guides

Review current Schaeffler profile rail systems and available replacement options.

SBC Linear Guides

Explore SBC linear rails and carriages for industrial automation and retrofit applications.

WON Linear Guides

Review WON profile rail systems for new and replacement linear-motion applications.

Linear Automation USA Resources

Technical resources for linear rail selection, cut-to-length rail planning, and replacement applications.

Contact Linear Automation USA

Submit legacy guide information, photographs, and measurements for replacement assistance.

Sources & Technical References

Linear Automation USA — Interchange Services

Linear Automation USA specifically identifies discontinued linear-system replacement and interchange assistance as a core service.

Linear Automation USA — Schaeffler KWLT15-H-V2-G4

This current product page provides a real example of a Schaeffler carriage identified as an interchangeable replacement for the corresponding Ewellix LLT configuration.

THK — GK Series Interchangeable LM Guides

THK explains the difference between interchangeable GK components and set products, including the importance of preload and the application limits of interchangeable systems.

THK — GK Series ISO Interchangeability Announcement

THK states that applicable GK profile rails use mounting dimensions based on ISO 12090-1 or ISO 12090-2 and describes the conditions under which blocks and rails are interchangeable.

THK — LM Guide Selection Criteria

THK’s selection process demonstrates why replacement evaluation should include load, equivalent load, preload, static safety factor, life, accuracy, lubrication, and environmental requirements rather than dimensions alone.

THK — HSR Series

THK’s current HSR data illustrates the importance of checking block style, dimensions, radial clearance, accuracy standards, mounting geometry, and lubrication details for a specific guide family.

Next
Next

Linear Guide Troubleshooting: Noise, Binding, Play and Uneven Motion